Gaia: Backup and Restore From CLI (Clish)

Gaia: Backup and Restore From CLI (Clish)

This article provides a quick tutorial on how to make a Gaia: backup and restore from the CLI (Clish shell) in Gaia. Depending which version of Gaia you are using, you may or may not have the option to perform a backup or restore from the Web GUI under the “Maintenance” section or you may only have SSH access – having the skill to do this from the command line is important either way.

For the methods below the following apply:

  • x.x.x.x should be replaced by the IP of the server
  • myuser should be replaced by a valid username for the server.
  • mybackupfile.tgz should be replaced by the name of your backup file
  • You will be prompted for the password on the command line if you are using FTP or SCP

Backup

The add backup command is what we use to initiate a backup from the CLI. We also need to pass a parameter to define where the backup is to be saved: local, FTP, TFTP or SCP:

  • To save a backup locally:
    • add backup local
  • To save a backup on a remote server using FTP:
    • add backup ftp ip x.x.x.x username myuser password plain
  • To save a backup on a remote server using TFTP:
    • add backup tftp ip x.x.x.x
  • To save a backup on a remote server using SCP:
    • add backup scp ip x.x.x.x username myuser password plain
add backup local

Note:

 

  • You can use the show backups command to see the status of any current and completed backups.
  • Backup configurations on Check Point appliances are stored in /var/log/CPbackup/backups/
  • Backup configurations on Open Servers are stored in /var/CPbackup/backups/

 

Restore

To restore a backup we use the set backup restore command and as with the backup, we pass the relevant parameters:

  • To restore a local backup:
    • set backup restore local <TAB>
  • To restore a backup from a remote server using FTP:
    • set backup restore ftp ip x.x.x.x file mybackupfile.tgz username myuser password plain
  • To restore a backup from a remote server using TFTP:
    • set backup restore tftp ip x.x.x.x file mybackupfile.tgz
  • To restore a backup from a remote server using SCP:
    • set backup restore scp ip x.x.x.x username myuser password plain

Remember!

  • Restore is only allowed using the same Gaia version on the source and target computers.
  • Restore is only allowed using the same appliance type on the source and target computers.
  • The backup file name generated by the backup command should not be renamed and must not contain spaces.
  • When backing to an SCP or FTP server, the backup file is put in the user’s home folder. When restoring from SCP or FTP the backup file is taken from the user’s home folder.
  • This is not applicable to VSX – to backup and restore VSX, see sk100395 for details.

Checkpoint: Find The Serial Number of IP Appliances Via CLI

Find The Serial Number of IP Appliances Via CLI

Sometimes it is necessary to find the serial number of IP appliances but you either don’t have physical access to the machine or someone has removed the sticker from the side or bottom. This article lists methods to retrieve the serial via the command line interface (CLI).

1. If you are physically next to the device, look for a label on the physical box.

2. If you are remotely accessing the firewall, log into Voyager, then look for “Unit SN” under the “Basic IPSO Information” section of the homepage.

3. On the CLI (either SSH or console), run the following IPSO command:

ipso[admin]# ipsctl hw:eeprom:serial_number

hw:eeprom:serial_number = 7Hxxxxxxxx4

OR

ipso[admin]# ipsctl -a | grep serial

ipso[admin]# ipsctl -a | grep "serial"
hw:eeprom:motherboard:serial_number = 94072202114
hw:eeprom:cpci_1:serial_number = 94072301073
hw:eeprom:cpci_2:serial_number = 94072301093
hw:eeprom:power_a:serial_number = SH52618
hw:eeprom:power_b:serial_number = SH52471
hw:eeprom:wx_3:serial_number = 94072202755
hw:eeprom:viper_4:serial_number = 94072300835
hw:eeprom:wx_1_1:serial_number = 94073601141
hw:eeprom:serial_number = 7Hxxxxxxxx4
hw:motherboard:serialnumber = 0
hw:chassis:serialnumber = 7Hxxxxxxxx4

This will give you all serial numbers related to different parts – the chassis is the last in the list and it is this serial number which is most commonly used.

4. In the clish shell (enter “clish” on the command line):

NokiaIP1260:102> show asset hardware
Chassis Serial Number: 7Hxxxxxxxx4
CPU Model: Pentium 4/XEON
CPU MFR: GenuineIntel
CPU Frequency: 2794587100
Memory: 1073741824
Disk 0 Model: STI Flash 8.0.0
Disk 0 Capacity: 128MB
Disk 1 Model: FUJITSU MHV2040AS
Disk 1 Capacity: 40007MB
Platform: IP1260
Bios Vendor: Hilo BIOS
Bios Version: 5.0-1.5
Bios Date: 10-19-2004
Motherboard Serial Number: 0
Motherboard Revision: B01
Motherboard Model: HILO-RCC1

5. For Nokia IP VPN devices:

hostname> show fru

MAIN (MOTHERBOARD) EEPROM FRU INFO:
-----------------------------------
Product Name: 10i
EEPROM info format rev num: 6
Number of slots: 0
MAC address count: 3
Base MAC address: 00:A0:8E:XX:XX:XX
System serial number: 7HXXXXXXXXX
System Agile part number: N806189001
System Agile H/W rev: C
Onboard MAC count: 3
System PCA Agile P/N base: 6187
System PCA Agile P/N suffix: 1

6. For former Nokia IPS platforms, please run the following command:

ip390ips ~ # cat /proc/nokia/nvram/serial_num

7. For UTM-1 EDGE devices, you can also use run the command:

EDGE:XX> show asset hardware

Checkpoint: Long Delay When Logging In Via SSH or Console

How to mitigate the issue where this a long delay when logging in via SSH or console.

When an SSH session is initiated to a linux box, the SSH server tries to perform a lookup on the client’s IP; in certain situations this is not going to be possible, e.g.:

  • the configured DNS server is offline
  • the firewall / smartcentre cannot talk to the configured DNS because of a policy
  • the external internet connection is down etc.etc.

This DNS timeout manifests itself as an incredibly long delay for the user trying to log in – fortunately there is a very quick fix for this:

  • delete the nameservers entirely!
  • configure nameservers that the machine is able to reach
  • use internal nameservers if your internet connection is flaky

This is the case for all Checkpoint linux-based machines as well as IPSO and Gaia.

Exit mobile version
%%footer%%